Best 16 Port PoE Switch in India (2026) – For Surveillance CCTV Cameras, WiFi Access Points, SMBs, Enterprise Networks, Outdoor Deployments

Best 16-port PoE switch – 

• For overall value: TP-Link ES220GMP / 16 PoE+ ports, 250W budget, 2 gigabit RJ45 + 2 SFP uplinks, Omada cloud management, VLAN, QoS, 250m extend mode, upgraded replacement for the popular TL-SG1218MPE
• Best for medium offices and surveillance: D-Link DGS-F1018P-E / 16 gigabit PoE+ ports, 2 SFP uplinks, 150W budget, 250m long-range PoE, 6kV surge protection, DIP switch modes for VLAN/QoS/Extend, widely available across India under ₹12,000
• Best enterprise L3 PoE switch at an affordable price: Grandstream GWN7812P / 16 gigabit PoE+ ports, 4x 10G SFP+ uplinks, Layer 3 with OSPF/RIP, 240W budget, 112 Gbps switching capacity, embedded controller, GDMS cloud, 802.1X/RADIUS/TACACS+
• Best L2+ alternative if L3 is overkill: Grandstream GWN7802P / 16 gigabit PoE+ ports, 4 SFP uplinks, 240W budget, L2+ managed, embedded controller, same security stack as GWN7812P at a lower price
• Best for outdoor and tower deployments: MikroTik netPower 16P / 16 gigabit PoE-out ports, 2x 10G SFP+, IP54/IP55 outdoor enclosure, dual DC input (24V and 48V), pole/mast/hose clamp mounting, RouterOS or SwOS dual-boot

TP-Link ES220GMP: the upgraded SG1218MPE - Best overall value

The ES220GMP is TP-Link's Omada-generation replacement for the TL-SG1218MPE, which was one of the most widely deployed 16-port PoE switches in India for CCTV and office use. The hardware upgrade path is straightforward: same 16 PoE+ ports with 250W total budget (up to 30W per port, IEEE 802.3af/at compliant), same 2 gigabit RJ45 + 2 SFP combo uplinks, but now with Omada Cloud Essentials integration for centralized remote management.

Switching capacity is 40 Gbps with a 29.76 Mpps forwarding rate and 15 KB jumbo frame support (per TP-Link's datasheet). The ES220GMP supports up to 250 meters of PoE distance in Extend mode, which is a genuine advantage for surveillance deployments where cameras are placed far from the switch location. Standard PoE range is 100 meters; Extend mode drops the data rate to 10 Mbps but pushes power delivery to 250 meters over Cat5e or better cable.

One Reddit user in r/homelab noted that the SG1218MPE (the predecessor) ran stable for over two years powering 12 UniFi access points without a single PoE restart. The ES220GMP inherits that same reliability with the added benefit of cloud monitoring. The metal rackmount chassis includes proper heat dissipation design rated up to 50°C operating temperature, which matters for Indian deployments.

Best for: CCTV systems with up to 16 IP cameras, office deployments powering access points and VoIP phones, anyone upgrading from the TL-SG1218MPE who wants Omada cloud visibility.

Not for: Setups needing more than 250W PoE budget (some 16-camera 4K deployments can push past this). Environments needing 10G uplinks or L3 routing.

D-Link DGS-F1018P-E: India's workhorse PoE switch - Best for medium offices and surveillance

The DGS-F1018P-E is one of D-Link's most popular PoE switches in India, and it shows up in a huge number of CCTV installations for a simple reason: it's cheap, it works, and D-Link has 220+ collection centers across 130+ locations in India for warranty service. That last point matters more than specs when you're deploying at scale across multiple sites.

Specs: 16 gigabit PoE+ ports (IEEE 802.3af/at, up to 30W per port), 2 SFP uplink slots, 150W total PoE budget, and 6kV surge/lightning protection. The 150W budget means you can realistically power about 10-12 devices at typical PoE draw (8-15W each for cameras and access points) before hitting the limit. If you need to power all 16 ports at 30W each, you'll need a switch with a higher budget.

The DIP switch on the front panel provides four operating modes without any software configuration: VLAN mode (isolates ports 1-16 from each other), Extend mode (8 ports support 250m at 10 Mbps), PoE mode (auto-detects and restarts crashed PoE devices), and QoS mode (prioritizes video traffic). This hardware-based mode selection is valuable for installers who don't want to deal with web interfaces during deployment.

Best for: Budget CCTV deployments across India where D-Link's service network is a priority. Installations needing surge protection (6kV). Quick-deploy setups where DIP switch modes eliminate software configuration.

Not for: Deployments needing more than 150W PoE budget. Environments requiring managed features like 802.1X, ACLs, or SNMP monitoring. The DGS-F1018P-E is unmanaged.

Grandstream GWN7812P: the most affordable L3 PoE switch - Best enterprise and advanced IT

The GWN7812P is where this list gets interesting for enterprise buyers. It's a full Layer 3 managed PoE+ switch with 16 gigabit PoE ports, 4x 10G SFP+ uplinks, a 240W PoE budget, and 112 Gbps switching capacity (per Grandstream's datasheet). Layer 3 means it supports inter-VLAN routing with OSPF and RIP, which eliminates the need for a separate router to route traffic between VLANs. For multi-floor or multi-department networks, this is a significant simplification.

The 10G SFP+ uplinks future-proof the switch for high-bandwidth aggregation, and the 240W PoE budget distributes up to 30W per port with smart dynamic allocation. Grandstream's embedded controller manages other GWN-series devices directly from the switch, and GDMS cloud platform provides remote monitoring. Security features include ARP inspection, IP Source Guard, 802.1X with RADIUS and TACACS+, and DoS protection.

At a price point significantly below comparable L3 PoE switches from Cisco or HPE Aruba, the GWN7812P is arguably the best value enterprise PoE switch available in India today. Available on the FGTech Store with full warranty support.

Best for: Enterprise campuses and multi-VLAN environments needing L3 routing with PoE. Deployments requiring 10G uplinks and dynamic PoE allocation. Grandstream ecosystem users.

Not for: Small deployments where L3 routing is unnecessary. Non-Grandstream environments where the embedded controller advantage doesn't apply.

Grandstream GWN7802P: when L2+ is enough - 

If the GWN7812P's L3 features are more than you need, the GWN7802P offers the same 16 gigabit PoE+ ports with a 240W budget, but at Layer 2+ instead of Layer 3. It has 4x 1G SFP uplinks (not 10G), 40 Gbps switching capacity, and the same embedded controller and GDMS cloud management. The security stack is identical: 802.1X, RADIUS/TACACS+, ARP inspection, DHCP snooping.

The practical difference: the GWN7802P cannot do inter-VLAN routing on its own. You'd need an upstream router or L3 switch to route between VLANs. If your network is flat or has only 2-3 VLANs with routing handled at the firewall, the GWN7802P saves you money without sacrificing PoE capability or management features. Also available on the FGTech Store.

Best for: SMBs needing a managed PoE switch with strong security features and cloud management, where inter-VLAN routing is handled upstream.

Not for: Networks requiring L3 routing at the access layer or 10G uplinks.

MikroTik netPower 16P: purpose-built for outdoor PoE - Best for outdoor and tower deployments

The netPower 16P (CRS318-16P-2S+OUT) is the only outdoor-rated switch on this list. It packs 16 gigabit PoE-out ports and 2x 10G SFP+ uplinks into an IP54/IP55 weatherproof enclosure rated for -40°C to +70°C. MikroTik designed it specifically for tower, mast, and pole mounting, and it ships with hose clamps and a fastening kit for that purpose.

Here's what makes this switch unusual: it has no onboard voltage converter. The PoE output voltage matches the input voltage. Connect a 24V power supply, and the ports output 24V passive PoE. Connect a 48V supply, and you get standard 802.3af/at 48V PoE. You can even connect both simultaneously, and the switch auto-selects the correct standard per port. This flexibility is ideal for ISP and WISP deployments where different access points require different voltages.

Performance specs from MikroTik's datasheet: 72 Gbps switching capacity, 36 Gbps non-blocking throughput, 53.6 Mpps forwarding rate. It dual-boots RouterOS (license level 5) and SwOS, giving you the choice between full routing capability and simple L2 switching. Power supply is not included, which adds to the initial cost but lets you match the PSU to your specific voltage and power requirements.

Best for: Outdoor WISP and ISP tower deployments powering multiple access points. Surveillance systems with cameras mounted on poles or building exteriors. Any environment where the switch itself must be exposed to weather.

Not for: Indoor rack deployments (any indoor PoE switch would be cheaper and simpler). Users who want a plug-and-play experience, since the netPower 16P requires deliberate PSU selection and voltage planning.